Effect of thermal treatment on hot-pressed isotopically modified boron carbide (10)B4C
DOI:
https://doi.org/10.52340/jns.2019.19.145Abstract
Образцы керамики 10В4С были получены методом горячего прессования при температуре 2100 °С и давлении 30 МПа. Образцы отжигали в вакууме при 1800 °С. Проведены оптические и растровые микроскопические исследования. Изучены физико¬механические свойства керамики. Установлено влияние термической обработки на обрабатываемость, трещиностойкость, твердость, модуль упругости, а также на механическую прочностькерамики.
References
V. Domnich, S. Reynaud, R. A. Haber, M. Chhowalla. Boron carbide: Structure, properties, and stability under stress. J. Am. Ceram. Soc., 2011, 94, 11, 3605-3628.
Z. Mestvirishvili, I. Bairamashvili, V. Kvatchadze, N. Rekhviashvili. Thermal and mechanical properties of B4C-ZrB2 ceramic composite. J. Mater. Sci. & Eng. B, 2015, 5, 9-10, 385-393.
K. Gillet, G. Roma, J.-P. Crocombette, D. Gosset. The influence of irradiation induced vacancies on the mobility of helium in boron carbide. J. Nucl. Mater., 2018, 512, 288-296.
Yu. A. Bykovskii, K. N. Zaitsev, P. J. Kervalishvili, I. N. Nikolaev, A. A. Portnov, S. O. Shalamberidze. Neutron fluence sensor based on boron carbide. Tech. Phys. Lett., 1993, 19, 7, 457-458.
P. J. Kervalishvili, G. S. Karumidze, Sh. Sh. Shavelashvili, G. I. Kalandadze, S. O. Shalamberidze. Semiconductor sensor for neutrons. Sensors & Actuators A, 1993, 36, 43-45.
P. J. Kervalishvili, S. O. Shalamberidze Yu. A. Bykovskii. Oriented boron carbide films produced by laser spraying. Proc. Am. Inst. Phys., 1991, 524-527.
H. Werheit, M. H. Manghnani, U. Kuhlmann, A. Hushur, S. Shalamberidze. Mode Gruneisen parameters of boron carbide. Solid State Sci., 2017, 72, 80-93.
A. Nino, A. Tanaka, Sh. Sugiyama, H. Taimatsu. Indentation size effect for the hardness of refractory carbides. Mater. Trans., 2010, 51, 9, 1621-1626.
A. U. Khan, V. Domnich, R. A. Haber. Boron carbide-based armors: Problems and possible solutions. Am. Ceram. Soc. Bull., 2017, 96, 6, 30-36.
В. Д. Рисованый, А. В. Захаров, Е. П. Клочков, В. Б. Пономаренко, Е. М. Муралева, Т. М. Гусева. Поглощающие материалы стержней управления ядерных реакторов, 2012, Ульяновск, 57-95.
T. G. Abzianidze, A. M. Eristavi, S. O. Shalamberidze. Strength and creep in boron carbide (B4C) and aluminum dodecaboride (a-AlB12). J. Solid State Chem., 2000, 154, 1, 191-193.
G. I. Kalandadze, S. O. Shalamberidze, A. B. Peikrishvili. Sintering of boron and boron carbide. J. Solid State Chem., 2000, 154, 1, 194-198.
H. Werheit, S. Shalamberidze. Advanced microstructure of boron carbide. J. Phys. Cond. Matter, 2012, 24, 38, 385-406.
T. Maruyama, Sh. Onose, T. Kaito, H. Horiuchi. Effect of fast neutron irradiation on the properties of boron carbide pellet. J. Nucl. Sci. & Technol., 1997, 34, 10, 1006-1014.
Y. Morohashi, T. Maruyama, T. Donomae, Y. Tachi, Sh. Onose. Neutron irradiation effect on isotopically tailored nB4C. J. Nucl. Sci. & Technol., 2008, 45, 9, 867-872.
I. A. Bairamashvili, M. V. Galustashvili, J. Sh. Jobava, V. G. Kvatchadze, Z. Z. Mestvirishvili. Composite ceramics based on boron carbide enriched in isotope nB as a promising radiation resistant structural material. Nano Studies, 2013, 8, 305-310.
T. Jianga, H. Jinb, Zh. Jina, J. Yanga, G. Qiaoa. An investigation of the mechanical property and thermal shock behavior of machinable B4C/BN ceramic composites. J. Ceram. Proc. Res., 2009, 10, 1, 113-116.
B. M. Moshtaghioun, A. L. Ortiz, D. Gomez-Garcia, A. Dominguez-Rodriguez. Toughening of super-hard ultra-fine grained B4C densified by spark-plasma sintering via SiC addition. J. Eur. Ceram. Soc., 2013, 33, 1395-1401.
G. R. Anstis, P. Chantikul, B. R. Lawn, D. B. Marshall. A critical evaluation of indentation techniques for measuring fracture toughness - I. Direct crack measurements. J. Am. Ceram. Soc., 1981, 64, 533-538.
Downloads
Published
Issue
Section
How to Cite
